Two stainless steel black oxide coated screws.
Fits Barswitches and killswitches with 2 screws
Does NOT fit single screw cable clutch kits!
2 screws sold per kit
If your looking for a switch that one way powers one thing and the other way powers something else this is it.
One example for wiring this switch 2 ways would be a horn button for 2 different things.
For example if this switch is switched one way lets say up it lets the horn button activate the horn
If this switch is switched down it could make the horn button activate the air shifter.
Other uses could be activating nitrous via the horn button.
This switch can be wired many ways this is just an example.
PMR Barswitch Accessories
$7.95
Replacement switches for all barswitches.
$11.95
PM-400 DPDT Double Position Double Throw on/on Black switch for barswitch.
If your looking for a switch that one way is off and the other is only on while pressing the switch this is it.
It is normally off and while pressing it it supplies power otherwise known as a momentary switch.
Uses for this could be purging nitrous
letting out air via electric solenoid for air ride.
PTT button for communications
or even opening a garage door.
This switch could wired many ways these are just an examples.
$11.95
PM-401 SPST Single Position Single throw off/Momentary Black switch for barswitch.
If your looking for a switch that is off in the center and on one way and also on the other way this is it.
The best example for this switch would be used for headlights. In the center the lights would be off. If the
switch was switched up it coulld be for the high beams and if it was switched to the down position it could be for low beams. This switch could wired many ways these are just an examples.
$11.95
PM-402 DPDT on/off/on Black switch for barswitch.
This is your basic on/off switch. It can be wired for anything you need to turn on or off.
Lights, Leds, nitrous, turbo controls, computers, etc.
This switch could wired many ways these are just an examples.
This is the standard switch that comes with all PMR Barswitch assemblys.
$11.95
PM-403 SPST on/off Black switch for barswitch (standard replacement for barswitch).
This is your basic on/off switch. It can be wired for anything you need to turn on or off.
Lights, Leds, nitrous, turbo controls, computers, etc.
This switch could wired many ways these are just an examples.
This is the same as the standard switch that comes with all PMR Barswitch assemblys except in RED.
$11.95
PM-403R SPST on/off Red switch for barswitch (standard replacement for barswitch in RED).
This is similar to the PM-400 except only single position and is RED, this means it has 3 terminals on the back and only one circuit. The pm-400 has 6 terminals and 2 circuits.
$11.95
PM-404 SPST on/on RED switch for barswitch.
If your looking for a switch that one way powers one thing and the other way powers something else this is it.
One example for wiring this switch 2 ways would be a horn button for 2 different things.
For example if this switch is switched one way lets say up it lets the horn button activate the horn
If this switch is switched down it could make the horn button activate the air shifter.
Other uses could be activating nitrous via the horn button.
This switch can be wired many ways this is just an example.
Same as PM-402 but RED.
If your looking for a switch that is off in the center and on one way and also on the other way this is it.
The best example for this switch would be used for headlights. In the center the lights would be off. If the
switch was switched up it coulld be for the high beams and if it was switched to the down position it could be for low beams. This switch could wired many ways these are just an examples.
$11.95
PM-405 DPDT on/off/on RED switch for barswitch.
If your looking for a switch that is off in the center and on momentary one way and also on momentary the other way this is it.
We started carrying this switch because many people had a need for it for air ride suspension. Here is an example. Center off, switch up while holding it would air up and hold down and it would air down. It can be wired many ways.
It is a normally off in the center switch with up and down momentary positions.
It has 6 terminals in the back with 2 circuits.
This switch could wired many ways this is just an example.
$11.95
PM-406 DPDT mom/off/mom Black switch for barswitch.
If your looking for a switch that is off in the center and on momentary one way and also on momentary the other way this is it.
We started carrying this switch because many people had a need for it for air ride suspension. Here is an example. Center off, switch up while holding it would air up and hold down and it would air down. It can be wired many ways.
It is a normally off in the center switch with up and down momentary positions.
It has 6 terminals in the back with 2 circuits.
This switch could wired many ways this is just an example.
This switch is the same as the PM-406 just in RED
$11.95
PM-406R DPDT mom/off/mom RED switch for barswitch.
Image shown is a representation only. Exact specifications should be obtained from the product detail.
Image shown is a representation only. Exact specifications should be obtained from the product detail.
Image shown is a representation only. Exact specifications should be obtained from the product detail.
Image shown is a representation only. Exact specifications should be obtained from the product detail.
Image shown is a representation only. Exact specifications should be obtained from the product detail.
Image shown is a representation only. Exact specifications should be obtained from the product detail.
Image shown is a representation only. Exact specifications should be obtained from the product detail.
Image shown is a representation only. Exact specifications should be obtained from the product detail.
PM-300 Stealth Screw Kit
Image shown is a representation only. Exact specifications should be obtained from the product detail.
$49.95
Many people have asked us to make a back barclamp so they can mount our barswitches or killswitches on any bike with a 7/8 diameter handlebar. So here it is! This will allow you to mount any killswitch or 2 bolt (hydraulic bolt pattern PM-53, PM-50, PM-54, PM-45, PM-47 etc) Barswitch made by PMR. Many people use this for drag bikes with no clutch lever or you can now add switches to dirtbikes or quads. We use this to mount switches on our KTM dritbike(see picture below). One switch is used for the 8" HID headlight and the other is used for the fan)
This is CNC machined and then black anodized to match the barswitches and killswitches.
PM-78B Black Barclamp
Mounted on a KTM 525 XC-W
This is not a cheap back clamp. It is quality! It is strong. It is CNC machined Aircraft aluminum then anodized to match the barswitches.
Your One Stop Motorcycle Speed Shop
